![]() |
Exposure test failed and nothing prints - Printable Version +- Elegoo 3D Printers Forum (https://www.elegoomars.com/forum) +-- Forum: Troubleshooting (https://www.elegoomars.com/forum/forumdisplay.php?fid=8) +--- Forum: General Troubleshooting (https://www.elegoomars.com/forum/forumdisplay.php?fid=11) +--- Thread: Exposure test failed and nothing prints (/showthread.php?tid=513) Pages:
1
2
|
RE: Exposure test failed and nothing prints - Gauntfield - 06-23-2020 (06-23-2020, 12:49 PM)zemerick Wrote:(06-23-2020, 11:53 AM)Gauntfield Wrote:(06-20-2020, 08:28 AM)Meh Wrote: Hey Gauntfield. Yeah. Mine goes directly to the end stage where you can see the LEDs underneath. It doesn't even pretend it's going to work like yours. That would be even more frustrating! Hope you get yours sorted out Very true, I havent opened the Orange30 yet but it looks like the corners of the screen protector are not rounded like the elegoo Ill take a peek later tonight and see if they match up at all ![]() RE: Exposure test failed and nothing prints - Gauntfield - 06-23-2020 well they gave me firmware 4.3.4 and a firmware clearing file to try and it still didnt work ![]() guess ill just wait ![]() RE: Exposure test failed and nothing prints - fromFDMtoSLA - 06-24-2020 please upload the files here - everybody is looking for a update for the "4.3.3"- version --- THX RE: Exposure test failed and nothing prints - Gauntfield - 06-24-2020 Ill toss them up here when I get home today ![]() RE: Exposure test failed and nothing prints - Gauntfield - 06-24-2020 Firmware 4.3.4 And firmware clear tool Copy both files to root of USB drive Boot up printer or power printer on Put in USB drive with files Print update.sh4 file first Printer beeps and stuff and will reboot on it's own Print the ALFPGA213_SPI_MIPI_P316_CTB_1440P_140M_FF file and it updates RE: Exposure test failed and nothing prints - tca7050 - 07-05-2020 (06-24-2020, 02:25 PM)Gauntfield Wrote: Firmware 4.3.4 This Firmware work for ELEGOO MARS PRO? How can I check the Firmware installed in my Printer? I have the same problem described in this post. Just could I print one Rooks and the second one just printed like 35%, after that nothing attach the bed (metal base).... my printer don't show me any error when I do the EXPOSURE test, and the CLEAN BASE test, the only difference is in the exposure test the screen show me a frame rectangle and in the clean test just a solid white rectangle. Anybody knows if the test must be done with the bed (metal base) up or down? Thanks so much. RE: Exposure test failed and nothing prints - cliffyk - 07-05-2020 (06-23-2020, 12:49 PM)zemerick Wrote:(06-23-2020, 11:53 AM)Gauntfield Wrote:(06-20-2020, 08:28 AM)Meh Wrote: Hey Gauntfield. Yeah. Mine goes directly to the end stage where you can see the LEDs underneath. It doesn't even pretend it's going to work like yours. That would be even more frustrating! Hope you get yours sorted out I would not even think too hard about doing that--these screens and/or motherboards, and/or that completely mickey mouse connector seem to be astoundingly delicate, I too seem to have toasted an MB while swapping out the screen, don't know how. The power was disconnected of course throughout the procedure but it would not pass the test after installation--returned the screen for another (gotta' like Amazon Prime) but that ooo would not work--gotta' be the MB at this point says i. So i sent the whole printer back to Amazon; This was in fact the second one i returned, the first came with a cracked LCD. Amazon sent me a 'snot-gram' about abusing their return policies, but did refund the money. Next i bought a new MARs (also from Amazon), a "silver" one as it was $10 less--it is working great so far, with about 250 hours on it. We'll see what happens when the LCD needs replacement. I REALLY do NOT like that crummy little connector... RE: Exposure test failed and nothing prints - Gauntfield - 07-09-2020 (06-24-2020, 02:25 PM)Gauntfield Wrote: Firmware 4.3.4 (07-05-2020, 11:48 AM)tca7050 Wrote:Dont believe so....When I received this from Elegoo it was for the regular Mars(06-24-2020, 02:25 PM)Gauntfield Wrote: Firmware 4.3.4 RE: Exposure test failed and nothing prints - mirina.faria - 10-05-2020 (06-05-2020, 03:19 PM)Meh Wrote: Hi. Thanks for your reply. |